1986 Corvette R-12 to R-134a Conversion

Friendly format provided to inquire about automotive a/c systems.
Archived Forum

Moderators: bohica2xo, Tim, JohnHere

kenlou
Posts: 50
Read the full article
Joined: Thu Dec 15, 2022 9:55 am

Re: 1986 Corvette R-12 to R-134a Conversion

Post by kenlou »

My FSM agrees with Tim. 80% of 2 3/4 lbs
kenlou
Posts: 50
Joined: Thu Dec 15, 2022 9:55 am

Re: 1986 Corvette R-12 to R-134a Conversion

Post by kenlou »

I will call my local Chevy dealer tomorrow
User avatar
Tim
Site Admin
Posts: 1280
Joined: Tue Apr 12, 2016 2:19 pm
Location: Scottsdale, Arizona
Contact:

Re: 1986 Corvette R-12 to R-134a Conversion

Post by Tim »

The higher capacity listing is most likely for an A6 compressor, which this does not have. Also, there is or was enough refrigerant to engage the clutch if "All" the electrical was operating correctly. Jumping the clutch coil only provides data for a single system component.

The data I posted came from ALLData, 2023
Image
------------------------------
Please support ACKITS.com for your Auto A/C Parts and Tool needs.

Help Support the Forum
kenlou
Posts: 50
Joined: Thu Dec 15, 2022 9:55 am

Re: 1986 Corvette R-12 to R-134a Conversion

Post by kenlou »

Thanks Tim. I am doing diagnostics on the bcm also
kenlou
Posts: 50
Joined: Thu Dec 15, 2022 9:55 am

Re: 1986 Corvette R-12 to R-134a Conversion

Post by kenlou »

JohnHere
Kenny, it might be worth calling your local Chevrolet service department to see what they can tell you.
I called several and none can go back to 1986. They are all relying on ALLDATA. They polly know more about UFOs than the 86 Corvette.
So I am going with my GM Service Manual...which states 2 3/4 lbs R-12....which translates to 36 oz of R134 (80% amount of original R-12).
tbirdtbird
Preferred Member
Posts: 1448
Joined: Sat May 02, 2020 1:48 pm
Location: Texas

Re: 1986 Corvette R-12 to R-134a Conversion

Post by tbirdtbird »

Just FYI, the 80% number is not hard and fast...it may require closer to 90% to properly function. Bottom line, start with 80% and add from there as needed. Somewhere in the archives here is a procedure for charging an unknown system posted by bohica (Brad)
When considering your next auto A/C purchase, please consider the site that supports you: www.ACKits.com
kenlou
Posts: 50
Joined: Thu Dec 15, 2022 9:55 am

Re: 1986 Corvette R-12 to R-134a Conversion

Post by kenlou »

tbirdtbird
Just FYI, the 80% number is not hard and fast...it may require closer to 90% to properly function. Bottom line, start with 80% and add from there as needed.
Yes, I had heard that and that was my plan. Thanks.
User avatar
Tim
Site Admin
Posts: 1280
Joined: Tue Apr 12, 2016 2:19 pm
Location: Scottsdale, Arizona
Contact:

Re: 1986 Corvette R-12 to R-134a Conversion

Post by Tim »

We're talking about a Vette here with an accumulator. The inlet and outlet on the evap should be close in temp. So charge to 80% and feel the difference. Slowly add more until they feel the same.
------------------------------
Please support ACKITS.com for your Auto A/C Parts and Tool needs.

Help Support the Forum
kenlou
Posts: 50
Joined: Thu Dec 15, 2022 9:55 am

Re: 1986 Corvette R-12 to R-134a Conversion

Post by kenlou »

Tim
We're talking about a Vette here with an accumulator. The inlet and outlet on the evap should be close in temp. So charge to 80% and feel the difference. Slowly add more until they feel the same.
Thanks.Wanna buy a vette? :lol:
kenlou
Posts: 50
Joined: Thu Dec 15, 2022 9:55 am

Re: 1986 Corvette R-12 to R-134a Conversion

Post by kenlou »

9.jpg
9.jpg (88.5 KiB) Viewed 2828 times
Does anyone know anything about the triangle shaped stamp on the GM R4 compressor body? Does it signify anything, polarity?
Post Reply